ASTM B167 Nickel Alloy Tube Inconel 600 Tube Inconel 600 Seamless Tube

• Type: Stainless Steel Pipes
• Standard: ASTM, DIN
• Grade: 600 Series
• Model NO.: Inconel 600
• Certification: AISI, ASTM
• Shape: Round
• Technique: Cold Rolled
• Surface Treatment: Polished
• Transport Package: Wooden Pallet
• Specification: OD 6-630mm
• HS Code: 7304319000
• Production Capacity: 500000kgs

Product Description

Inconel 600 Tubing Nickel Alloy 600, Inconel 625 Pipe Inconel 600 Welding Pipe

Inconel 600 (UNS N06600) Ni 76.0, Cr 15.5, Fe 8.0 Description

Ni 72.0, Cr 15.5, Fe 8.0 Mn 1.0 C 0.15 Cu 0.5 Si 0.5 S 0.015

High Performance Alloys stocks and produces Inconel 600 in this grade in the following forms: Bar, wire cuts, sheet, plate, strip, tube, pipe. Request Quote on this grade.

 

Overview

Inconel 600 is a nickel-chromium alloy with good oxidation resistance at higher temperatures, with good resistance in carburizing and chloride containing environments.

Inconel 600 is a nickel-chromium alloy designed for use from cryogenic to elevated temperatures in the range of 2000 deg F(1093 deg C). The high nickel content of the alloy enables it to retain considerable resistance under reducing conditions and makes it resistant to corrosion by a number of organic and inorganic compounds. The nickel content gives it excellent resistance to chloride-ion stress-corrosion cracking and also provides excellent resistance to alkaline solutions.

Its chromium content gives the alloy resistance to sulfur compounds and various oxidizing environments. The chromium content of the alloy makes it superior to commercially pure nickel under oxidizing conditions. In strong oxidizing solutions like hot, concentrated nitric acid, 600 has poor resistance. Alloy 600 is relatively un-attacked by the majority of neutral and alkaline salt solutions and is used in some caustic environments. The alloy resists steam and mixtures of steam, air and carbon dioxide.

Alloy 600 is non-magnetic, has excellent mechanical properties and a combination of high strength and good workability and is readily weldable. Inconel 600 exhibits cold forming characteristics normally associated with chromium-nickel stainless steels.

Typical corrosion applications include titanium dioxide production (chloride route), perchlorethylene syntheses, vinyl chloride monomer (VCM), and magnesium chloride. Alloy 600 is used in chemical and food processing, heat treating, phenol condensers, soap manufacture, vegetable and fatty acid vessels and many more.

 

Characteristics

• Resistant to a wide range of corrosive media. The chromium content gives better resistance than Alloy 200 and 201 under oxidizing conditions, at the same time the high nickel gives good resistance to reducing conditions.
• Virtually immune to chlorine ion stress corrosion cracking.
• Demonstrates adequate resistance to organic acids such as acetic, formic and stearic.
• Excellent resistance to high purity water used in primary and secondary circuits of pressurized nuclear reactors.
• Little or no attack occurs at room and elevated temperatures in dry gases, such as chlorine or hydrogen chloride. At temperatures up to 550C in these media, this alloy has been shown to be one of the most resistant of the common alloys.
• At elevated temperatures the annealed and solution annealed alloy shows good resistance to scaling and has high strength.
• The alloy also resists ammonia bearing atmospheres, as well as nitrogen and carburizing gases.
• Under alternating oxidizing and reducing conditions the alloy may suffer from selective oxidation.

Applications

• Thermocouple sheaths.
• Ethylene dichloride (EDC) cracking tubes.
• Conversion of uranium dioxide to tetrafluoride in contact with hydrofluoric acid.
• Production of caustic alkalis particularly in the presence of sulfur compounds.
• Reactor vessels and heat exchanger tubing used in the production of vinyl chloride.
• Process equipment used in the production of chlorinated and fluorinated hydrocarbons.
• In nuclear reactors uses are for such components as control rod inlet stub tubes, reactor vessel components and seals, steam dryers and d separators in boiling water reactors. In pressurized water reactors it is used for control rod guide tubes and steam generator baffle plates etc.
• Furnace retort seals, fans and fixtures.
• Roller hearths and radiant tubes, in carbon nitriding processes especially.

 

Fabricating INCONEL ® Alloy 600
Inconel 600 is non-magnetic, has excellent mechanical properties and a combination of high strength and good workability and is readily weldable. Alloy 600 exhibits cold forming characteristics normally associated with chromium-nickel stainless steels.

600 sheet and plate are almost exclusively supplied in the annealed condition. Bar stock may need to be stress relieved, or annealed before performing any heading operations.

 

Chemistry

Chemical Requirements
	Ni	C	Mn	Cr	S	Si	Fe
Max		.15	1.0	17.0	.015	.5	10.0
Min	72.0			14.0			6.0

 

Tensile Data

Mechanical Property Requirements
	Ultimate Tensile	Yield Strength (0.2% OS)	Elong. in 2 in. or 50mm or 4D, min., %	R/A	Hardness
Cold Worked/As worked
Min	110 KSi	85 KSi	10
Max
Min	760 MPa	585 KSi
Max
Hot Worked/As Worked
Min	90 KSi	40 KSi	25
Max
Min	620 MPa	275 MPa
Max

D- Forging quality is furnished to chemical requirements and surface inspection only. No mechanical properties required.

Specifications

Form	Standard
Metal Type	UNS N06600
Bar	ASTM B166 AMS 5665 Din 17752
Wire
Sheet	ASTM B168 AMS 5540 Din 17750
Plate	ASTM B168 AMS 5540 Din 17750
Tube	ASTM B167
Pipe	ASTM B167
Fitting	ASTM B366
Forging	ASTM B564 Din 17754
Weld Wire	FM 82/ ERNiCr-3
Weld Electrode	FM 182/ ENiCrFe-3
Din	2.4816

 

Machining

Machinability Ratings

MACHINING DATA
Carbide tools are suggested For Rates Better Than 50% Of Type 304.
Machining Type	Suggested starting rates are:
Single Point Turning :	Roughing - 0.15" depth, 0.015"/rev feed -175 SFM Finishing - 0.025" depth, 0.007"/rev feed - 200 SFM
Drilling :	1/4" Dia hole - 0.004"/rev feed - 60 SFM 1/2" Dia hole - 0.007"/rev feed - 60 SFM 3/4" Dia hole - 0.010"/rev feed - 60 SFM
Reaming :	Feed - same as drilling - 100 SFM
Side And Slot Milling :	Roughing - 0.25" depth - 0.007"/tooth feed - 125SFM Finishing - 0.050" depth - 0.009"/tooth feed - 140SFM
These rates are for carbide tools, Type C-2 For Roughing, Drilling And Reaming. Type C-3 For Finishing.

 

INCONEL® is a registered trademark of the INCO family of companies.

 

Product picture:

Packing: